Grid to Ground Calculator

Free combined scale factor calculator for surveyors, engineers and layout crews. Enter a location and elevation in any U.S. state plane zone, then convert distances and coordinates between grid and ground.

1 Find your combined scale factor

Negative in the lower 48. On your GPS data collector or the NGS GEOID18 tool.

2 Convert a distance

Filled in by step 1, or type your own.

3 Scale coordinates (optional)

Makes project ground coordinates (sometimes called modified state plane) by scaling every point about one fixed origin. Use the same origin and factor for the whole project, and write both on the plans.

For planning and checking. Confirm the factor and origin with your project surveyor before staking or recording. Your data stays in your browser.

What is grid to ground?

State plane coordinates sit on a flat map grid, but you measure on the real ground, which is curved and usually well above the ellipsoid that the grid is based on. So a distance measured with a total station or tape is slightly different from the same distance computed from state plane coordinates. On most sites the ground distance is longer, by anything from a few hundredths of a foot to more than a foot per mile.

The combined scale factor converts between the two. Multiply a ground distance by it to get the grid distance; divide a grid distance by it to get the ground distance. It is the product of two parts: the grid scale factor, which depends on where you are in the zone, and the elevation factor, which depends on how high the site is.

How the combined scale factor is calculated

Elevation factor = R / (R + h)
Combined scale factor = grid scale factor × elevation factor
Grid distance = ground distance × combined scale factor
Ground distance = grid distance ÷ combined scale factor

h is the ellipsoid height: the elevation above sea level (NAVD 88) plus the geoid height, which is negative across the lower 48. R is the earth's mean radius of curvature at your latitude, about 20.9 million feet. The grid scale factor comes straight from your zone's official NAD83(2011) definition. This is the same method the National Geodetic Survey (NGS) uses for the combined factor on its control datasheets.

Worked example: Boise, Idaho

NGS control mark BOI B (PID AC5198) in Boise, Idaho West zone. Enter these in the calculator and you get the same numbers.

Latitude, longitude43.5634354, -116.2203823
Northing, easting (US ft)691,588.119, 2,499,993.038
Elevation (NAVD 88)2,850.52 US ft
Geoid height (GEOID18)-55.29 US ft
Grid scale factor0.99995109
Elevation factor0.99986642
Combined scale factor0.99981751
1,000 ft on the grid, on the ground1,000.183 ft

NGS publishes a combined factor of 0.99981750 for this mark. We checked the calculator against 32 NGS control marks in 15 zones across 11 states, using the ellipsoid heights NGS publishes, and every one matched to within 0.01 parts per million.

Which elevation should I use?

Use the average elevation of the project area. Across a typical site the elevation factor changes by about 0.05 parts per million per foot of elevation, so one project-average factor is usually fine unless the site spans a lot of elevation or distance. If you only have the elevation above sea level, enter it and leave the geoid height blank: the factor will be off by roughly 2 to 5 parts per million in the lower 48 (0.01 to 0.03 ft per mile). For the exact answer, add the geoid height from your GPS data collector or the NGS GEOID18 tool.

Questions

What is a combined scale factor?

It is the number that converts distances between the state plane grid and the ground. It combines the grid scale factor (where you are in the zone) with the elevation factor (how high the site is). Multiply ground distances by it to get grid; divide grid distances by it to get ground.

Do I multiply or divide?

Ground to grid, multiply by the combined scale factor. Grid to ground, divide. A quick check: at most sites the factor is a little less than 1, so ground distances come out slightly longer than grid distances.

What are ground coordinates or modified state plane?

Many projects scale state plane coordinates by one combined factor about a fixed origin so that coordinate distances match tape and total station distances on site. Those ground coordinates no longer match state plane, so the plans should state the factor, the origin and the zone. Step 3 of the calculator does this scaling and downloads the results.

How big is the difference between grid and ground?

It depends on elevation and position in the zone. Near sea level close to the zone's central line it can be a few hundredths of a foot per mile. In Boise at about 2,850 ft it is close to 1 ft per mile, and at higher sites in Colorado or Montana it can be well over 1.5 ft per mile.

What is the difference between ellipsoid height and elevation?

Elevation (orthometric height, NAVD 88) is height above sea level, what plans and benchmarks show. Ellipsoid height is height above the GRS80 ellipsoid, what GPS measures directly. The difference is the geoid height, about -10 to -35 meters (-30 to -115 ft) across the lower 48.

Does Leica iCON or Captivate do this for me?

Yes. Leica field software can apply a project scale factor or a ground coordinate system so crews work in ground distances. Set it up the same way on every controller and instrument on the job. If you want help setting that up, our training covers it.

Tools and help from Datum